Choose your new
AUTOLift3000
AUTOLift3000 Standard
3 types of accessories included
AUTOLift3000 Premium
6 types of accessories included
Accessories Detail
-
Used for lifting cars with fragile body parts (e.g. plastic aftermarket skirts). Make sure the entire rubberized pad surface rests on the rail!
-
The drill adapter is designed as breakable. When the maximum height of the AUTOLift3000 is accidentally exceeded, the adapter crown snaps off to protect the lift. That's why we include a set of 4 with the product.
-
Should be used whenever the AUTOLift3000 is in the lifted position, to fix it in place. Make sure to remove the safety pin before lowering the car!
-
Hang the AUTOLift3000 on the wall of your garage. Very popular with home users in particular. Aside from saving space, these hangers also add a touch of style to your garage.
-
Need to lift your car on gravel, sand, grass, or any other uneven surface? No problem, just attach these rails and you're ready to go. The rails also protect floors you don’t want scratched.
-
A safety accessory to hold up the lifted side of the vehicle. Make sure to remove the stand before lowering the car! Adjustable height: 670 - 1,150 mm / 26.3 - 45.3 in.
FAQ
-
The AUTOLift3000 is certified up to 6,614 lbs / 3,000 kg. While the device has been stress-tested to much greater weights, for your safety it is nonetheless strictly forbidden to exceed the certified limit.
-
Standard power drills only. Make sure to keep the hammer function off if it has one. Never use any tool that generates shocks (e.g. impact or pneumatic wrench). The recommended torque to lift the device is 309 inch-lb / 25 ft-lb.
-
The tool can only be used with unibody passenger cars, which trucks typically are NOT. The car also must not exceed the maximum weight capacity of 6,614 lbs, and must have ground clearance at least a little higher than the height of the folded product (115 mm / 4.5 in). To lift a lower-riding car, you will need a ramp.
-
For as long as needed (weeks, months, a year).
-
Please feel free to contact our customer service line at info@autoliftproduction.com.
-
Even when a car is lifted by its center of mass, a certain amount of effort is needed to tilt it over. It cannot really tip over on its own, unless you substantially change the weight distribution by removing heavy parts (e.g. engine, gearbox, clutch). When doing work that removes or adds substantial weight to the car, always use the support stand to prevent unexpected tilting.
-
Without factory schematics or specialized equipment, you will need to use trial and error. For a front-engined car, try putting the lift pads about 4 in (10 cm) behind the front wheels. Lift the car up just a little, and see if it tilts easily. If not, lower it back down and move the AUTOLift3000 closer to the end that didn't lift off the ground.
It’s fun! -
On some cars (e.g. the Mercedes-Benz CLA and some other German cars), the plastic parts are firmly attached to the undercarriage frame. On cars where this is not the case, use the provided skirt pads. Place the pad on the AUTOLift3000 contact surface and make sure it will come to rest on a load-bearing undercarriage part. Before lifting the car, check that the lift pads don't rest on any fragile body parts. We cannot be held responsible for any damage to your car that may result from failure to follow these instructions.
-
The maximum width of the AUTOLift3000 is 62" / 158 cm.
-
The product does not require maintenance. You should still check all its components for damage (e.g. from shipping or handling) before using it. If used correctly, the product can last a very long time: Some of our original customers have used the same unit for over 20 years.
-
Yes. The AUTOLift3000 is covered by a 3-year warranty.
-
Yes, we have distributors and service centers worldwide. Please contact our customer service at info@autoliftproduction.com if there are any problems.